+ Reply to Thread
Results 1 to 7 of 7

Thread: Engine temp fluctuation Volvo Penta Gsi 4.3L

  1. #1
    Join Date
    Nov 2005
    Location
    Poway
    Posts
    173

    Default Engine temp fluctuation Volvo Penta Gsi 4.3L

    I took my boat out on the bay last weekend. Nothing strenuous. I noticed that after getting away from the launch the engine temp (according to gauge) jumped up to 180. I cut the motor and looked for something stuck on the RSW intakes on the outdrive but didn't see anything. Put the outdrive back down and slowly motored on. Temp was down around 120, then 160 (where I would expect it), then back to 180... If I would slow down to a crawl the temp would go all the way back down to around 120!?!?!?

    I have it on the trailer and I'm going to replace the things on my list to check are impeller and the thermostat. Any other ideas why the temp would vary so dramatically?

    Thanks,

    Brian
    Brian Groff
    "Little Provider"
    1974 Blackman Fishmachine 20

  2. #2
    Join Date
    Oct 2005
    Location
    Vista,Ca
    Posts
    194

    Default

    Hey Brian,
    Running warm @ higher rpm.
    Ok kinda sounds like a circulation issue at first but it really could be a number of things.
    Simple to complex...
    Think back to any recent repairs. What if?
    Verify actual temp with a secondary gauge ie. Pocket thermometer ect. I use a lazer digital type.
    Ignition timing/ loose distributer
    Ck all elec connections from sending unit to gauge and fix if skeptical. Especially grounds
    Loose v- belt to water pump.
    Intake screen restriction
    Raw water pump defective
    Restriction in any plumbing including exhaust elbows
    T/stat sticking
    That may keep you busy for awhile
    Royal Hook

  3. #3
    Join Date
    Apr 2004
    Location
    Spring Valley
    Posts
    2,692

    Default

    I'll vote impeller. Start with the easy stuff and work your way down the list.

    Mike
    NoSlack-------------------------------------------<'(((>{

  4. #4
    Join Date
    Nov 2005
    Location
    Poway
    Posts
    173

    Default

    Thanks guys!
    I have been reading online about debris/ broken impeller fins lodging in the thermostat resulting in some like what I described, but the quick swing to 180 degrees on the gauge really concerned me.

    When I figure this out I'll report back.

    -Brian
    Brian Groff
    "Little Provider"
    1974 Blackman Fishmachine 20

  5. #5

    Default

    If you were in the bay could it just be sea junk (kelp, eel grass)? I do a lot of diving in the kelp beds and my D4 hates the kelp - constant issues in there.

  6. #6
    Join Date
    Nov 2005
    Location
    Poway
    Posts
    173

    Default

    Replaced the impeller and thermostat. When I was removing the hoses I noticed a significant amount of what looked like rusty flakes inside the tubing. I could bend the tubes and the layer of this stuff would break up and come out of the tube. At any rate. Took the boat out last weekend to see if replacing the T/stat and impeller made a difference with the overheating under load, and it did not.

    I can cruise around the bay all day just above idle and the engine will run at 140-150 degrees. Once I increase the the RMP's the temp goes above 180.

    So now I am moving on to the exhaust risers/manifolds.

    -B
    Brian Groff
    "Little Provider"
    1974 Blackman Fishmachine 20

  7. #7
    Join Date
    Nov 2005
    Location
    Poway
    Posts
    173

    Default

    After replacing the risers and manifolds, it looks like the overheating issue has been resolved. Just to give you guys an idea of what was going on in the cooling system:

    After taking a look at the T/stat it made a lot of sense that this would be the culprit...



    And after seeing the build up in the water jackets for the risers and manifold, it made sense that this would probably be effecting the cooling as well...

    Riser


    Exhaust manifold


    At any rate, it seems to have been an overheating issues caused by more than one component. Thanks guys for your help and advice.

    -Brian
    Brian Groff
    "Little Provider"
    1974 Blackman Fishmachine 20

+ Reply to Thread

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

     

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts